If you connect a new device to the cable modem, such as a router or new computer, the modem must be reset. First, reset the modem by removing the power cord then plugging it back in, then reboot your computer or router.

Previously, we suggested that people use Mac modem cables; however, it has come to our attention that there is no one standard Mac modem cable. Since correct modem operation on a NeXT depends upon a correctly wired modem cable, buying a Mac cable is not a good idea. Some Mac cables do not allow dial-in and no Mac cable allows the use of hardware flow control. For these reasons, we are recommending that only cables that meet NeXT specifications be used.

If no, please review "communications port conflicts" to ensure that the com port you are using is enabled and properly configured. Once you have ascertained that the port is working properly, retry communications. If the problem persists, then proceed to the next question. If yes, then there could be a communication port conflict between the portable and another device assigned to that port.

Regional Bell Operating Companies are sometimes tariffed and will only allow (with perfect telephone line conditions) 53K. Tariffs are established by the FCC and by state Public Utility Commissions. Because analog lines are a little noisy (static), your modem will automatically slow down to accommodate for noise. It is normal for 56K modems to connect between 39 - 51K. This is still very good performance.

This is a common question because many things can cause this. First off, it is important to remember that while 56K is the theoretical limit a modem can connect on a normal analog phone line, NO modem ever connects at 56K. About the best a modem could ever achieve is 53K and a modem that connects at 40K or better in most cases is doing pretty well. Causes of slower connection speeds include: Unconditioned or poor quality phone lines.

First, the highest connection the FCC allows over standard phone lines is 53.3k. This is the fastest connect rate you can get. If your are connecting in the 40k-50k range, this is considered good for most dial up connections. If you connect at a rate less than you would like, your modems 56k protocol may not be compatible with ours. We support the fastest and most common protocols across most of our network, 56k Flex, v.90 and v.92. You can attempt to update your modem drivers.

With the standard plan, you can only connect one computer to the modem. See the terms and conditions page for information and costs to setup a proxy server.

We don't have arbitrary limits. NCF's resources are yours to use. We don't put limits on how long you can stay connected, how much disk space your email or website can use, etc ... as long as there are resources available for others to use as well. For example, dial-up access is unlimited as long as there are modems available for others; if all the modems become busy, NCF's modem sharing system gives priority to people with less connect time that day.

When connecting the WinGate machine to the Internet through a Cable Modem, you first need to be sure to have two Network Interface Card's (NIC's) installed in that computer. One connected directly to your Cable Mode and the other connected directly to your internal network. ( You should not try connecting the Cable Modem directly to your network hub as this will cause severe security issues.

For additional information on the OpenVMS Ask The Wizard (ATW) area and for a pointer to the available ATW Wizard.zip archive, please see Section 3.8. The following sections contain information on OpenVMS and IP networking, as well as IP printing topics.

The DSL modem is an external device that connects to your computer's network interface card (NIC) via a standard 10BaseT cable. Yes, but CCI Net will not provide network technical support. CCI Net will only provide technical support for the DSL line and the primary PC on which it was installed.

Each GSM device can have one way to connect. In any case, GSM modems are connected to the computer's serial port. Each mobile phone usually has a kit to connect to the computer. Read the documentation for your mobile phone or contact your service provider.

a. The modem connects to the computer with an Ethernet cable. The modems can be connected directly to a router, wired or wireless so you can share your system with the rest of the family.

Check to see if the phone line is connected correctly to your system. Make sure it is connected to the LINE jack of the modem. Go into the Device Manager and remove all items listed under "Modems". To remove an item in Windows XP and Windows 2000, select the item, click the Action menu, choose Uninstall. To remove an item in Windows 98 and Windows ME, select the item and click Remove. If the installation asks you for the drivers point the installation to drivers.

The connect rate reported at logon is just a snapshot of that moment. Your actual rates will fluctuate up and down during the time you are connected. Normal connect rates on analog lines will be between 21.6 and 28.8. It is difficult to achieve 33.6 connect rates on analog lines.

No, a modem is not needed for a ResNet connection. ResNet uses an Ethernet network that requires an Ethernet card (hardware) for your computer. [ back to top ]

In order to use the VTel DSL Service with your computer you will need to install a 10BaseT network adapter (also known as an Ethernet card). Once you have installed the adapter you will simply connect it to the DSL Modem using a 10BaseT cable (provided with your modem). Your DSL Modem connects to the existing phone jack in your house and you are ready to go!

A. When attaching a modem to the serial (RS232) port, verify that the port assigned to your modem matches the COM port assigned to the Serial Port on the Port Replicator. To check this: Go to Device Manager and check the COM port that is assigned to Serial on USB (COMx) under the heading Ports(COM&LPT), where "x" is the COM port assignment. Device Manager can be reached by right-clicking on My Computer and choosing Properties.

The PC to which you are trying to synchronize or connect must be protected by NMS for PDA. If you are trying to connect to a PC other than the one from which you installed NMS for PDA, you must install the PC component of NMS for PDA using the same Product Encryption Key.

Ans: Connect one end of a 1394a cable to the device, and the other end to the computer. The cable must be no longer than 4.5 meters. Each piece of cable in a daisy-chain network is called a hop. There can be up to 16 hops (for a total of 72 meters) between any two devices. Moreover, when 1394a bridges are used, a network can consist of up to 64,449 devices.