NO, the auger sets in a "T" slot groove in the back of the shaft and may have slid forward just enough to come out of that slot. If you turn the Auger in a circular motion while pushing in back in you will feel it slide into that "T" slot coupler and then you will not be able to turn the auger by hand anymore.

The Auger that we exclusively manufacture is a screw type that carries the warm chocolate from the basin to the top crown through a cylinder. The advantage over a pump is it eliminates the possibility of clogging and reduces clean up time.

Many millions of zinc parts are held together by screws with no problem at all. Because zinc has a low coefficient of friction it is often useful to use either a "star" washer or to serrate the underside of the screw head to prevent it unscrewing, particularly if the parts are subject to vibration. If the design requires maintaining a minimum tensile stress in the screw and temperatures are likely to be above 1500 F, there is a possibility that stress relaxation could occur.

Send it back to Eagle or have someone who can solder the jack back on fix it for you. This would only take a couple of minutes. Back to Top | Back to FAQ

A half-hour radiodrama series produced in Minnesota, specializing in satire and horror. It was originally produced at KUOM-AM (770 Radio K) in Minneapolis between 1994 and 1997. We haven't done any scientific tests or anything, but we're pretty sure that it was the funniest and scariest comedy and horror radio-drama anthology series ever produced on KUOM-AM from 1994 to 1997.

Threads' home station is KUOM-AM (Radio K) in Minneapolis, which is currently airing the show at 9pm on Wednesdays. The original run of 39 episodes was syndicated on public-radio and college stations across the U.S. and Canada, thanks to the arcane magic of satellite transmission and the even more arcane magic of sending boxes of cassettes through the mail. Thus we fulfilled a lifelong dream to annoy people thousands of miles away. We were played on these and other radio stations:

Dependent upon the flow and dusting characteristics of the powder. Typically, to achieve a reasonable accuracy without too much dust generation 1-2 kilos per second would be a normal maximum. In terms of containers per minute, speeds up to 400CPM are filled on our continuous motion rotary fillers. See Technology Page for further details.

Not reading relevant materials or attending self-development investment/financial planning seminar like those of the Institute of Financial Planning.

This is a collection of the quesions people most commonly ask me. Perhaps you were wondering about these topics yourself, but "didn't want pry." I hope this page helps satisfy any lingering curiousity you may have! :)

We only use cocoa butter as a base in our suppositories. There are no chemical stabilizers used. Because of this, an occasional a suppository may crumble or break. To fix it, simply put the remaining suppositories (still inside their plastic wrapper) in a bowl full of warm water with the points facing down for 5 minutes or until they have become soft. Next put the suppositories in the freezer for 30 minutes. They will now have reformed and they should be ready to use again.

You need to check with your counselor if already enrolled. If new appointment, please watch court deadlines on court minute orders or paperwork.

Most packaged "drug store" cigars include non-tobacco ingredients such as paper, saltpeter (for even burning) and PG or Glycerin (to prevent them from drying out). Quality cigars contain only tobacco. Most quality cigars contain top-of-the-line leaves, and are made with long-filler (the leaves run from end to end. "Good" cigars are generally only available from Tobacconists.

Good ones don't come lose and if they do then you need to learn how to be a bit more gentle with your microphone technique. Some rock musicians apply loads of duct tape to hold everything together, including the stands! The secret is quite simply to buy good mics and look after them, that applies to any equipment really.

NO. ALL HOLES ARE DRILLED THE MORNING OF THE FISHING CONTEST. NO ADDITIONAL HOLE DRILLING IS ALLOWED BY ANY CONTESTANT. YOU MAY WANT TO BRING AN ICE CHISEL AND ICE SCOOP TO CLEAR ANY ICE THAT MAY FORM PRIOR TO THE CONTEST STARTING.

If the consumer really feels that the carpet is related, it helps to suggest to them that they might have a hot water extraction done on their carpet. In new construction you have a lot of new odors,with all the odors of a new construction, it’s hard to tell what is specifically causing a reaction. The best way to eliminate all the new odors is to open the windows and ventilate for approximately 48 to 72 hours.

Many styles of goggles have replacement parts such as headstraps and nosepieces available for much less than the cost of a new pair of goggles. For example, a new pair of Speedo "Sprint" goggle costs about $6.00 but a replacement headstrap is only about $1.50. It may make sense for you to anticipate this need and purchase spare headstraps in advance.

No. The rules don’t change and someone’s breaking them because they didn’t read this FAQ, or can’t be bothered to stick to them. What happens next is, firstly, that FashCon buyers (almost all of whom tell me that these are the kinds of notices they signed up for and read) spot the rulebreaker in 20 seconds and either discount that designer forever, or decide that there’s no point reading future notices from that store.

You can usually tape the broken ends together and advance the ribbon a couple of turns before reinserting the ribbon carriage to get back to a working condition. If the take-up reel has a lot of used ribbon built up on it, it may be best to remove the used portion of the ribbon from the take-up reel and tape the end of the good ribbon onto the take-up reel.