You need to mount the uncompressed host partition as usual. In this partition, you can see the compressed partiton as large file (the CVF, Compressed Volume File). It usually has names like 'dblspace.NNN', 'drvspace.NNN' or 'stacvol.XXX'. The whole compressed partition is inside this file.

The secondary DOS partitions are found after ALL the primary partitions. For example, if you have an “E” partition as the second DOS partition on the second SCSI drive, you need to create the special files for “slice 5” in /dev, then mount /dev/da1s5: # cd /dev # sh MAKEDEV da1s5 # mount -t msdos /dev/da1s5 /dos/e

When you re-install your operating system you must use the same version and Key which you used originally.

When your hard drive gives lots of errors, you usually will reinstall your OS if the errors can't be fixed. By reinstalling your OS you will have a smoother running PC. Junk build up after using your pc a couple of years, so reinstalling wouldn't sound like a bad option. If this is all done then, we can begin by first formatting your hard drive. After the format is done reboot (ctrl+alt+del) and go into your system bios. Check with your PC manual if you don't know how to do this.

You need to attach your Linux drive to another computer which can boot from Windows, and then restore the files on that computer using R-Studio. No matter how that system recognizes your drive, R-Studio should access it. You may also run R-Studio Agent Emergency which boots up from the single floppy and allows R-Studio to access data on that computer over the network.

Kemplar.com provides all the necessary English drivers for reconfiguring the device in the event reinstallation is necessary. We are also happy to provide, free of charge, Disk Images of the English install so as to make this process quicker. We can make these Disk Images available on CD in both Norton Ghost and Powerqest DriveImage format. You will simply need to purchase one of said programs and create a set of boot disks to take advantage of these Images.

Before you reinstall operating system you need keep your current license "alive" Please do following: If you could not do this procedure you need to contact technical support with your registration details (your Registration name and/or email address used during registration.) and new Serial Number you've got after your re-install Cafe Manager. No. Cafe Manager does not have any interaction with network server and it does not performs any of the server or proxy tasks.

Software only solutions can easily be hacked and cannot offer any real protection outside the operating system. The Recovery Card hardware card can protect against such intrusion or corruption by intercepting them outside the operating system or at the hardware level.

You user name is stored in the registry of the operating system. Therefore a reinstallation or hard disk change results in the loss of your user name. Unless you unregistred your user name in the registry before, Reminder will not allow you to register with the same name. Reminder assumes that the name is occupied by another user. To prove that you are legitimate to use the name you are asked to enter an identification code.

Head Lice Cure comes in a kit with 4 - 16oz. containers of the solution. This may seem like a lot of product

During startup, the "service gfs start" script (/etc/rc.d/init.d/gfs) gets called by init. The script checks /etc/fstab to see if there are any gfs file systems to be mounted. If so, it loads the gfs device driver and appropriate locking module, assuming the rest of the cluster infrastructure has been started.

Yes. DOS extended partitions are mapped in at the end of the other ''slices'' in FreeBSD, e.g., your D: drive might be /dev/da0s5, your E: drive, /dev/da0s6, and so on. This example assumes, of course, that your extended partition is on SCSI drive 0. For IDE drives, substitute ad for da appropriately if installing 4.0-RELEASE or later, and substitute wd for da if you are installing a version of FreeBSD prior to 4.0.

Where c0 is the controller number. t0 is the target (SCSI ID number) (omit for ATAPI/IDE) d0 is always 0 for SCSI, the drive # for ATAPI/IDE p0 is the partition; DOS is the first partition here /mnt is the mount point You can use the normal UNIX commands to copy files, 'cp', etc., after that to move the data. DOS filenames are in the old 8.3 format (lower case) for Solaris 2.5.1, in long filename format (lower case) for Solaris 2.

Older versions of the Installer (and the NetBSD kernel) only check the first 8 partitions for NetBSD-style partitions. If you have a lot of partitions on your drive (including the partition map and driver partitions), it could be that your NetBSD partition falls beyond the first 8. So, the Installer won't recognize it. Try re-ordering the partitions on your drive and see if that fixes the problem.

Yes. Just backup as usual but add '-d /mnt/nfs' or wherever your partition is mounted; don't use '-Oc' or '-Ot' at all; just '-Oi -d /root'. Then, after booting from the media which Mondo generates, you need to type 'ISO' at the console.

First you'd need to read the drive's geometry and write down some values. You can use HDToolbox or linux fdisk for that. The BlocksPerTrack value is taken from the sectors/track value. Note that it has absolutely nothing to do with the physical disk geometry - FAT only uses it as a multiplier. If you get the Cylinders eg from HDToolbox or using the Linux fdisk like this: sudo fdisk -u -l /dev/hda, Then you'll need to set BlocksPerTrack=63.

Once at the "A:\>" type "format c: /q" (without the quotations) then press "Enter". Once at the "A:\>" type "E:" (without the quotations) then press "Enter". Once at the "E:\>" type "setup" (without quotations) then press "Enter".

There is no inherent mapping between drive letter and partition that can be used to determine one from the other. A basic data partition must be identified by its partition GUID.

Back to ToC An utility called ISOnoHFS, written by Sauro Speranza, must be launched before inserting the CD-ROM. The Macintosh then mounts the ISO 9660 partition. This utility is very useful when testing the result of a hybrid CD-ROM on a Macintosh. The current version of this utility is version 2. Search for it from any search engine to locate a server on the Web. For an example, this link to Macinsearch was valid last time we checked (in march 2000). This utility only works with SCSI drives.