Freestanding stoves can be connected to chimneys built especially for them. The chimneys may be of masonry construction or be a factory-built metal system that's been designed, tested and listed for use with wood burning appliances. Freestanding stoves can also connect to an existing fireplace chimney, if the height and position of the stove's flue collar permits it. When this type of installation is done, the stoves may be called hearth stoves.

Installation of our hearth products must be done in strict accordance with local or national building codes, and the unit's installation manual. We recommend that our products be installed by a factory-trained Mr. Fireplace installer.

Yes. We recommend annual service of your fireplace by a qualified serviceperson. This will ensure that your appliance is functioning properly. Your decision really comes down to how much a priority heating efficiency is for you. If you want a lot of heat from your fireplace, you should consider a direct vent gas insert. From a cost standpoint, an insert will cost approximately five times the cost of a nice gas log set.

You will need to contact a Mr. Fireplace Sales Representative in your area. Refer to contacts for locations

Yes, but placement is key. Again the fan needs to draw cooler air from behind to operate and the surface on which the Ecofan is placed should never exceed 340ºC (650ºF).

Please make sure the flue is open before starting fire. NEVER remove hot ashes or partially burned loges. Please leave the ashes in the fireplace even if you are sure they are cold. It's easier to build a fire with a bed of ashes. If it becomes absolutely necessary to remove the cold ashes, use a metal container only. (Anything flammable, such as a paper bag or cardboard box, even if you are positive the ashes are cold, is extremely dangerous.

Unfortunately, no. You will need a wood pellet stove but if you don’t already have one, the savings you will realize in heating your home will more than pay for the stove. Some companies do offer converters which may be placed in fireplace inserts. Please check with your local hardware store or on the web to see if this option will work for you.

Attached means that the awning will use the house on one side and posts on the other side for support. The posts need to attach to concrete, either to a 4" nominal slab or concrete footings (engineering determines footing size). Freestanding means that the awning will not attach to the house and solely relies on posts at each side of the awning for support. Freestanding units require the posts be poured into concrete footings (engineering determines footing size) for the shear value.

Yes, it is possible. You will need a stack and a pedestal to do so. First, you must determine which model you have. To do so, measure the rectangular opening on the top of the unit. If the opening is 13 ¾” x 3 ¼,” you have either a Model 26000 Old Buck (Little) or a Model 27000 Old Buck (Regular). Order part # FA 260421 for the stack and part # FA P4171B for the pedestal. If the opening measures 16” x 3 ¾,” then you have Model 28000 Old Buck (Big).

If you already have a brick or stone fireplace, or a factory-built fireplace, and you want to convert it to gas, then the most cost-effective solution is an insert. If you are remodeling a part of your home that never had any kind of built-in structure, then you need a Direct Vent fireplace that does not require an existing opening or chimney.

Yes, we sell Mr. Flame Fireplace Glass Doors which are designed to work with the Fireplace Radiator™. Click here to view them.

Chances are there will be a gap between the insert and the inside of the fireplace. That is why we offer a range of faceplates designed to cover the gap. The faceplate also houses the on/off switch and fan control, so you don't have to crouch or bend down to operate your insert.

The SEND / RETURN connections provide for up to a 50:50 mix of the effect signal and the dry audio, but the INSERT points interrupt the signal path such that the entire audio path us routed through the external processor. Typically delay, reverb, chorus and other similar units are connected to the EFFECTS SEND / RETURN points. The INSERT jacks are better suited for compressor / limiters, aural enhancers and equalizers. Yes. In fact you can use all four outputs at once.

EPA Regulations are government regulations of wood burning appliances mandating that products sold after July 1, 1992, emit no more than 4.1 grams of particulate matter per hour for catalytic-equipped units and no more than 7.5 grams for non-catalytic-equipped units. When starting a fire, use plenty of crumpled newspaper and kindling. As a guide, fill the firebox completely with loosely crumpled newspaper and hold it down with at least ten pieces of finely-split dry kindling.

More than likely, yes. We commonly remove birds, rats, squirrels, raccoons and other animals from attics, crawlspaces, stove vents, fireplaces and other locations in homes, garages and sheds.

Carefully open the damper and, using a flashlight, look up the flue for signs of a build-up along the walls. Goggles are suggested for this. If the build-up is ?" or more, a cleaning is needed.

It is sometimes called a base-page. It is the foundation of the album and is attached to the binding of the cover by pins, hinges, clips and stitching.

The safest installation available for a woodstove insert is one that is lined to the top. Reasons to line a woodstove insert to the top include:

im buying a new ac ready furnace for my mobilehome,., i have the paperwork from the previous owners purchase of a new kenmore outside cooling condenser,tech info and so on but it does not say its a 1 ton or3 ton or3.5 ton ,HOW CAN I FIND OUT WHAT TONAGE IT IS SO I GET A PROPERAC READY FURNACE THE FURNACE IM LOOKING AT WILL HANDLE UP TO A 4 TON I am interested in purchasing an Eden PURE portable infared heater, Model 1000, which the internet site states is 5200 BTU.

The major difference between freestanding birth centers and hospital birth centers is that hospitals create policies to care for people who are sick, while freestanding birth centers design programs for healthy pregnant women. Also, freestanding birth centers are based on the midwifery model of care which approaches pregnancy and birth as a normal family event until proven otherwise.